tainless steel SAF and SDAF , ina SNV100-LPillow Blocks

corrosion proof flang bearing

Round Stainless steel Four-Bolt Heavy Duty Flange Bearing Unit

Oval stinless steel flange beating unit

Stainless steel ball bearings

Labyrinth seal



Centrifugal (CS) and Double bearing labyrinth seal (DS)


If dust and water get inside a bearing, this leads to premature failure. Therefore choosing the right protective seals is important for the working life of a bearing. The centrifugal seal (CS) is designed for harsh conditions where there is a risk of contamination. And if you want extra protection in a dusty, abrasive environment, you can choose the DS type.

Extreme Bearing centifugaal seal

Why choose a centrifugal seal?

Dusty, abrasive environments are one of the most difficult for bearings. Because when handling powders or in processes generating dust, the protection of bearings against contamination requires special consideration. Radial oil seals, such as the AS and SA seals made of nitrile rubber, are selected mainly for ordinary conditions. But they are generally unsatisfactory in harsh or dusty conditions. Over time, the nitrile rubber is attacked by dirt, water, sand and various other contaminants. Small particles get into the soft material of the rubber. And the lip can cause fretting of the shaft (causing a groove under the lip). Tiny particles of moisture on the shaft can be drawn past the lip. And a jet of water sprayed at high pressure directly at the lip seal penetrates past the seal into the bearing.

Extreme Bearing has developed the centrifugal seal to solve these problems! Many Extreme Bearing housings feature centrifugal seals specially developed to repel dirt and contaminants using centrifugal force generated by the shaft. The CS seal works for speeds up to 5 m/s and for temperatures from -25°C up to 95°C.

Triple barrier bearing labyrinth seal

CS seals are superior against sand, dirt and detergents

  1. Double lip centrifugal seal
  2. Grease-filled housing
  3. 2-RS bearing seal

Firstly, the centrifugal seal made of rubber attached to the shaft provides a primary barrier. Because itt repels dirt and contaminants using the centrifugal force generated by the shaft. Secondly, the bearing housing is filled with grease to prevent contaminants from entering and damaging the bearing. Finally, there is a type of bearing seal called 2-RS to protect the bearing.

bearing pillowblock labyrinth seal for ming

Working principle

The rubber of the CS-seal clamps around the shaft and is turning with the shaft vertically against the stator ring. Because the lips are positioned vertically against the stator ring, the dirt will be repelled by the centrifugal force from the sealing lips. The rotor ring can be moved eccentrically in relation to the stator ring. In this way, the centrifugal seal is able to absorb any misalignment of the shaft without creating wear on the rubber lips.

The grease passes the retaining edge through the lubrication channels under the stator ring and between the two sealing lips and stator ring. This makes sure that any dirt is flushed away. The clamping of the rubber rotor ring around the shaft means that the bearing can be assembled even on a shaft which has suffered light surface damage such as a groove.


The gaps between the lips of the centrifugal seal and the stator must be sealed to keep out dust and water. To improve bearing life for centrifugal shaft seals, it is recommended to use an automatic lubricator or to lubricate regularly. Only a small quantity of grease is necessary when slowly flushed into the bearing cavity to force dust and moisture away from the working parts.

Examples of grease diagrams using CS seals

If the contamination is only on one side of the bearing unit, a bearing labyrinth seal for combination, such as those shown in the diagrams, can be chosen. And by refilling the grease on this side, it will flow and be released from the bearing housing. Because of this, the contamination along with the grease will flow away from the sealing lips.

Double CS bearing labyrinth seal

Centrifugal seal

When applying the CS bearing labyrinth seal, it must be taken into account that it is not flush with the surface of the housing. And expands the dimensions of the housing slightly, as shown in the table.


d1 t
20 32 3
25 40 3
30 46 3
35 50 3
40 60 3
45 60 3
50 70 3
55 70 3
60 80 3
65 100 5
70 100 5
75 110 5
80 110 5
90 110 5
100 110 5
ange bearing mounted with labyrinth seal

DS, Double bearing labyrinth seal

DS Double seal

The DS (double seal) is a combination of a CS(centrifugal seal) together with a CC PTFE seal and has been developed for bearings used in abrasive environments.

This DS seal combines the advantages of two seals in a single seal set. CS seal means that the underlying CC seal has extra protection against abrasive particles.

Labirinth double bearingunit seal
Extreme Bearing centifugaal seal

Stainless steel bearing cover-spacer ring is used to make space for the labyrinth bearing housing seal.

Bearing pillowblock labyrinth seals
Stainless steel Spacer ring to mount labyrinth bearing seals
Size V
20 8.5
25 8.5
30 8.5
35 8.5
40 8.5
45 11
50 11
55 11
60 11
65 13
70 13
75 13
80 18
85 18
90 20
100 20

While using the DS seal, the installation length increases

When the DS seal is required in a bearing unit with a continuous shaf (cover side), the built-in length is greater. Because space has to be made in the bearinghousing by using an SR spacer ring.

Examples of grease diagrams using DS bearing labyrinth seals

test 2